Samsung TV Remote Not Working? How to Fix It
A Samsung remote that stops working usually needs charging (solar remotes) or new batteries, then a reset and a fresh pairing. Charge it, then hold Return and Play/Pause together for at least 3 seconds while pointing it at the TV. If nothing works at all, unplug the TV for 30 seconds, and test the remote’s infrared with your phone camera.
The short version: Charge the remote or change its batteries. Unplug the TV for 30 seconds. Then hold Return and Play/Pause for 3 to 5 seconds, about 1 foot from the TV, to pair it again.
Which Samsung Remote Do You Have?
Samsung has used a few kinds of remote, and the fix depends on which one is yours.
- SolarCell remote. The slim remote that comes with many 2021 and later Samsung TVs. It has a solar panel on the back and a USB-C port on the bottom edge. No batteries.
- Smart Remote with batteries. Older Smart Remotes look similar but take batteries.
- Basic remote. The long remote with a number pad. It works by infrared only.
Smart Remotes and SolarCell remotes connect over Bluetooth, so you don’t need to point them. They also have infrared as a fallback. A basic remote has to point at the TV.
Charge the Solar Remote
A SolarCell remote that’s run flat stops responding to buttons, or responds slowly. When it’s critically low, its light flashes for about 3 seconds when you press a button.
- Fastest: plug a USB-C cable into the port on the bottom of the remote. The light stays on while it charges and goes off when it’s full. Samsung doesn’t include the cable or charger.
- Slow: leave it solar panel up in daylight or under room lights.
Once the remote works again, many Samsung TVs show its charge under Settings › General › Power and Energy Saving › Available Remote Battery. On 2022 and later TVs, look under Settings › All Settings and then General & Privacy. Not every remote supports it.
Change the Batteries
On a Smart Remote or a basic remote, put in a fresh set of batteries. Don’t mix old and new. Weak batteries are the usual reason a remote works only some of the time.
Restart the TV
The TV can stop listening to the remote even when the remote is fine. Unplug the TV from the wall while it’s on, wait 30 seconds, and plug it back in. If your TV has a One Connect Box, unplug that too. Turn the TV on with its own control button.
Reset the Remote
SolarCell and Smart Remotes (2021 and later TVs): hold Return and Enter (the centre of the round navigation pad) together for 10 seconds. This basic reset usually keeps the pairing. If the remote doesn’t reconnect afterwards, pair it again (next section).
If that doesn’t help, do a full reset, which clears the pairing: hold Return and the button up and to the right of Enter together for 3 seconds. On many remotes that button has four coloured dots. Some remotes have only two buttons above the pad; use the one on the right.
Basic remote: take the batteries out, hold Power for 8 seconds, then put the batteries back in.
Pair a Smart Remote Again
- Turn the TV off and back on with the TV’s own power button, not the remote.
- Stand about 1 foot (30 cm) from the TV and point the remote at it.
- Hold Return and Play/Pause together for at least 3 seconds. Samsung’s US instructions say up to 5.
- Wait for a message on the TV saying the remote is connected.
If it won’t pair, unplug the TV for 30 seconds, plug it back in and try once more.
Test the Infrared With Your Phone Camera
Your eyes can’t see infrared, but a phone camera can.
- Open the camera on your phone.
- Point the remote at the lens and hold Power.
- Watch the screen for a flickering light at the tip of the remote.
No light? Put in fresh batteries or charge it and try again. Still no light means the remote has failed. If you do see the light, the remote is sending, so the problem is pairing or the TV. Point it at the Samsung logo, where the sensor is, and clear anything in the way, like a soundbar.
If the front camera shows nothing, try the rear one. Some phone cameras filter out infrared.
Use Your Phone While the Remote’s Out
You can keep watching. Samsung’s SmartThings app has a remote, and Remora, a universal remote for iPhone, works with Samsung smart TVs running Tizen (2016 and later). Both need your phone on the same Wi-Fi as the TV.
The first time Remora connects, the TV asks you to choose Allow, so it’s easier to pair a phone app while the remote still works. If the TV asks every time, see how to stop a Samsung TV asking to allow. The Samsung page lists what works and the settings to check.
If the TV is off and the remote is dead, you can still switch it on with the TV’s own button or from your phone. Our guide on turning on a Samsung TV without the remote shows where the button is and which setting the phone needs.
When to Replace the Remote
If the remote shows no infrared light in the camera test with a full charge or new batteries, or a Smart Remote won’t pair after a full reset and a TV restart, it’s time for a new one. Samsung sells replacements by TV model, so check the model number on the back of the TV before you order.
Questions
How do I know if my Samsung remote is charged?
On TVs that support it, look under Settings › General (or General & Privacy) › Power and Energy Saving › Available Remote Battery. The menu name varies by year and country. While charging by USB-C, the remote's light stays on and goes off when it's full.
Why does my Samsung remote work only when I'm close to the TV?
The remote is likely using infrared because its Bluetooth pairing was lost. Pair it again with Return and Play/Pause. If it still only works up close, charge it or change the batteries.
My Samsung remote stopped working after I used the SmartThings app. What now?
Samsung describes this on some 2022 TVs. Turn the TV off and on with its own power button. Then in SmartThings, open Settings › About SmartThings › SmartThings Guide and choose not to receive new device notifications.
Can I use my iPhone as a Samsung TV remote?
Yes. SmartThings and Remora both control Samsung smart TVs over Wi-Fi. The TV and the phone must be on the same network.